Search the Community
Showing results for tags 'fps'.
Found 3 results
My current setup is an i7-4790K, 32GB of RAM, 2 1080Tis in SLI, and 3 2560x1080 144HZ Gsync Monitors(configure in surround to 7990x1080 w/ bezel correction) When driving the full Lemans track I am unable to come close the 144FPS that the monitors support. I briefly hit 133 FPS and the CPU utilization was 47% and the GPUs were 79% and 85%. I am not experiencing any thermal issues as the neither the CPU or GPUs ever go above 53C. All of the graphics settings in the game are maxed out and AA is only set to high. Since I am pushing around the same amount of pixels as a single 4K display I assumed that I would get the same performance but I am not. I have seen posts of 1080Ti SLI setups getting 191FPS in PCars. Below is a spreadsheet that shows 1 lap at Lemans. It contains FPS and CPU and GPU utilization. If anyone knows what my issue is, your input would be greatly appreciated. https://docs.google.com/spreadsheets...it?usp=sharing
Hi! Im planning on getting three 27" 75Hz monitors next week and was wondering how well my Strix 1060 6Gb can run them. Right now on single screen in iRacing race with the Cadillac at Okyama I get min 130 -140 fps with everything turned high without V-sync or cockpit mirrors.
Spinelli posted a topic in rFactor 2Trying to run rFactor 2 with maxed-out graphics settings but just can't do it? Try the following: These settings (especially #2, #3, and #4) are "golden" and have transformed my gaming experience. They do not change the visual quality - to me - from fully maxed-out graphics settings, yet really boost my framerates, and therefore the overall experience, so much! Thanks to these settings, I can keep everything else absolutely maxed-out. 1. Anti Aliasing (Nvidia) - 8xCSAA instead of 4xAA / 16xCSAA instead of 8xAA - Slightly better performance AND image quality. If setting from the Nvidia Control Panel or Nvidia Inspector, then make sure to also set "antialiasing mode" to "override application settings" instead of "application controlled", and make sure the antialiasing in the rF2 configure screen is set to "None". If using AA from rF2 itself, then I believe Lvl 2 = 4xAA, Lvl 3 = 8xCSAA, Lvl 4 = 8xAA, and Lvl 5 = 16xCSAA, but don't quote me on that, plus, it may be different with different GPUs (780 Ti, here). 2. Shadows - "High" (4/5) - Visually speaking, you will hardly notice a difference between this setting and "Max". I don't notice it, I would need to do side by side comparisons to notice, but you sure do get better framerates (especially overall consistency around the track). 3. Shadow Blur - "Fast" (2/4) - Of course not as nice as "Quality" (lvl 4/4), but it also helps very nice with framerate and is hardly noticeable when you're actually playing (unless you play from an exterior cam eg. chase cam). Oddly enough, Fast (2/4) actually looks slightly better than "Optimized" (3/4) according to previous tests (from a build or 2 back). 4. Anisotropic Filtering - "8x" (6/7) - You almost certainly will not notice a visual quality difference between 8x and 16x (you will with 4x, though), and you also will most likely not get a framerate improvement when lapping on your own, but testing shows good framerate imrpovements when multiple cars are on screen (especially at the start, during the first couple laps, lots of cars on screen at once during a replay, etc.). Those settings are the difference between my framerate dropping and stuttering to as low as 45 fps/eye (total 90 fps - I use Nvidia 3D Vision 2), and having them at 60 fps/eye (total 120 fps). Maybe some rare drops to 58 fps/eye (116 total) or something, but hardly. That's a pretty massive gain for 3 settings that literally make no image quality difference to me, at all - and that's while using triple screens w/ multiview! If you still want to raise your framerates without lowering any in-game graphics then you have 2 more options (I recommend to everyone to do #5, regardless!). 5. Pre-Rendered Frames - "1" - In the Nvidia Control Panel (or Nvidia Inspector, I recommend Inspector since it has more adjustments and settings) select your rF2 profile, then change the setting (don't forget to hit Apply/Save/O.K.). Apart from gained fps in rF2, this will also decrease input lag for most users 6. In Nvidia Inspector set the following (I believe you can only adjust two of the following in the standard Nvidia Control Panel, however it may give the same result - fps-wise - but I'm not 100% certain, so I use Nvidia Inspector just to be safe): - Texture filtering - Anisotropic filter optimization: ON - Texture filtering - Anisotropic sample optimization: ON - Texture filtering - Quality: HIGH PERFORMANCE - Texture filtering - Trilinear optimization: ON Still want more framerates while hardly affecting image quality? 7. Circuit Detail - "High" - May achieve a higher and more consistent framerate around the track or at specific points around the track where you may be experiencing framerate drops. You may notice some far-away trackside objects not showing anymore, but it is a very small amount of stuff, and usually far off into the distance rather than actual track-side stuff. It is a very, very small image quality decrease for the amount of potential framerate increase it may bring on certain PCs and certain tracks. 8. Opponent Detail - "Medium" or "High" - May improve framerates when racing against other opponents, including possible large framerate improvements when racing against many opponents. These improvements will give you a very, very nice boost in rFactor 2 framerates without hardly affecting the image quality at all. Thanks for supporting rFactor 2 and ISI (Image Space Incorporated)! Happy racing! Here's an example of great results (I believe the three settings being referred to are #2, #3, and #4)source --> http://isiforums.net/f/showthread.php/20751-LG-34UM95-instead-of-tripples?p=324489&viewfull=1#post324489