Search the Community
Showing results for tags 'csw2'.
Found 1 result
Hello all Thought I'd share my CSW modding details, in case there are others who own the kit and feel restricted by the provided button pods, that come with the hubs. While existing pods are fine, if you tend to swap rims several times a day, using different button arrangements, even with multiple hubs, of which I have 3, the default set just isn't enough. As soon as he hubs became available some time ago, I began looking to mod the system with quick connectors to button plates with my own button arrangements, that would avoid the need to open up the hubs every time I want to swap a rim on any of them. First, it took me some time to find the right JST connectors for the HUB's PCB sockets. Took me a long time and a lot of experimenting with a few connectors that didn't work/fit. Micro ZH 1.5 4-Pin JST Connectors http://www.ebay.co.uk/itm/230865243993 These fit just fine, but I would still recommend cutting off its side tongues/ridges (that slot into female socket side grooves) with a sharp knife, otherwise they will be a bit too tight, as it's not a 100% the same grove system on Fanatec's and these JSTs. Now, you want to extend these, with the external connector sockets. I chose these ones at first, for half a year or so www.ebay.co.uk/itm/330991782233 only to replace them later with these, as they look and work a lot better and easier to plug/unplug quickly http://www.ebay.co.uk/itm/20-sets-Male-Female-4-Pin-Connector-with-wire-for-5050-3528-RGB-Led-Driver-Strip-/262154789544?hash=item3d09a4a2a8 They come with male and female wired ends, the latter being directly wired to the JST connectors in the first link (1.5mm pitch) and male halves wired to your buttons. So as you can see it's pretty simple. You are just extending the internal HUBs sockets outside of the hub enclosure, so yuo can connect various multi-button plates as they are needed for the car you are driving at the time. Here are a few, but not all of the button plates I use. Please note - the GT OMP wheel has also the knob implemented, but being unable to wire it well with a few connectors i wasted my money on (USB3 and similar) I gave up (for now) trying to extend its 10 pin connector, after an unsuccessful (partial success really, due to a sloppy wiring job) attempt to extend that too. It just sits there filling the hole I cut for it initially So there you go - a simple solution, if like myself you would like to use a bit more customised rims with your own button plates connected to the hub, instead of external 3rd party PCBs Same principle applies to wiring buttons direct to the rim, for some of them it's the best way. I am using this on 3 rims that simply would look bad with a button plate Of course there's also an issue with paddle shifters attached to the hub - you wouldn't want to have them on, if you are driving a gated manual shifter or sequential stick cars instead. You could of course, use a similar to the above system of mine - 2-pin JSTs for the paddle shifter connectors (1.5mm pitch ones, just like 4-pin ones) to extend them outside of a hub, but you'd also need to attach/detach the paddle switches. In my case, having 3 hubs really helps with this, as I have one with permanently mounted GT paddles, 1 with small paddles for small/formula types of rims and one without any. With this system, you can have multiple rims setup to suit different cars. After a year and a bit with this, having accumulated 3 hubs and 15 rims, I cannot believe I used to race an old lotus or a cobra with a BMW GT2 rim - that is in my eyes a blasphemy and should be punishable by death! Usually it takes 2.5 minutes quickest and up to 5-7 minutes (in a worst rim case scenario) to remount a rim and its button plate, so while not instant, it's still pretty bloody quick Additional infos, in case anyone's interested. For button plates I used A4 sized 3mm carbon fibre sheets, which are priced rather reasonably (about £20) and you can make 2-3 plates from one sheet/use the remains for paddles etc. Buttons from various eBay outlets, but I'm getting tired of seeing the most common plastic buttons used on everyone's button boxes and wheels these days (pictured here at the bottom part of sparco and momo rims plate). They are great, esp the feel of them, but far too common, so I tried to find alternatives and still believe FREX's buttons are the best aesthetically, even if they cost a bit more. Hope this helps someone like me. If anyone done anything similar already, feel free to show off here