Search the Community

Looking to take next step from my xbox one racing set up and would like to build my own PC. I have limited knowledge about components but can follow instructions and know which end of the the pug to use. I have about a $1200 budget for the PC alone. Am looking for a system that I can find instructions on how to build and can be expanded in the future. Thanks for your help.

Hi all from another Aussie on the forums in Perth. I've been browsing a little while now, since I got a set of the Samsung Odyssey VR goggles. After a bit of research, I then ordered the Thrustmaster T300 GT RS set , which led me to wanting g to build a cockpit (I've already built a number of flight Sim cockpits). I looked at the designs and although they were good, but I wanted something different, I thought it had to at least look similar to a car cockpit. So I used our Touring cars (Bathurst 1000 racing) as my "style" I also just happen to have a CNC with Aspire software in my garage so i started to design.... I styled the front to look like a touring car, (falcon or commodore) with a southern cross logo on the front with the seat going to have the HDT lion and helmet. (I haven't built the seat yet), I decided on the logo because its a good design and one I can do on my CNC. I made a few mistakes so far which I fixed some last night, moving the wheel back 200mm. This is a prototype I may sell it and make another. Thoughts and suggestions are welcome. The third image is my being impatient and testing before I put a seat in, glad I did as the wheel was too far back (more laid back like an F1.) I wanted more upright. I sat a few friends down with the CAR goggles on and I think the screams said it all.(from the ladies), the guy who tried (Mitch 20) said "Wooooow, this is the shit, love it" So this weekend I move it to the downstairs lounge before the wife realises, and work out a good way of covering it when not in use. I think getting everyone to try it also it to the wife.... For once I have a degree of WAF.

Hello, thank you for checking out my "How to" on building my simrig! I have attached zip files for you to download that have all the information needed for every single piece to build the rig, along with plans, sections, and elevations with some dimensions for reference. I will try to explain how I chose to go about assembling it below. - Attachments are at the bottom of this post, after the pictures. **** I strongly encourage you to take time and familiarize yourself with all of the information given before you begin construction. **** A few pieces of the build will require you to take some of your own dimensions to have it work best with all of your equipment. Refer to the "Piece Tickets.pdf". - For example, you will need to take specific dimensions of the monitor you decide to use. These will be very important in determining where the cutouts will be located for the monitor and front speakers, and how large they will need to be. **** If you have any questions about anything or see that I have left out something needed to build the rig, please send me a message or reply to this topic and I will do my best to explain anything you need. I would suggest that you reply to this topic, that way if anyone else has the same question they can get an answer just by following the posts. If you decide to build my rig, I would greatly appreciate it if you could add a picture of your finished build to this topic. I am very interested to see how you will make it your own, and if you decide to make any modifications to it. Feel free to change anything you would like about the build, I have only given information for how to build my rig exactly. - If you would like to play computer games on it, I currently do not have it designed with that in mind. If you wanted to though, a simple solution would be to put your computer inside the large panel that you use to access the back of the monitor & front speakers, Depending on how large the monitor is you use, it should be able to fit inside well. I would suggest that your computer has a good cooling system in it though, because it could get quite warm being enclosed in a small area. Key things to pay attention to: 1. All of my dimensions given are based on using 5/8" thick wood. If you use any thickness other than 5/8", many dimensions will be slightly off which will cause problems with pieces lining up correctly. If you use a different thickness of wood, you will need to add/subtract the difference it makes in all pieces that would be affected. 2. I used a 32" LG monitor. I would assume you could go up to a 36", but I have not verified that, and it would still depend on the overall dimensions of the monitor, and front speakers. You will need to reference dimensions given and make sure the monitor and speakers you choose will fit inside the designated areas for them. 3. Plan out ahead of time how you plan to finish the rig off. Whether you decide to add material, paint it, stain it, etc. You should figure that out before assembling the pieces so you know how hard it will be to finish off once fully built, or how much prep work you will need to do before assembling. 4. The plans I have designed were for my own personal preference, using a Fanatec CSR Elite wheel, Fanatec CSR Elite Pedals, and Fanatec CSR Shifter Set. Please review the dimensions given and figure out if they will work well with your equipment of choice, and personal preferences. Certain dimensions were not provided (such as location of the seat, etc.) because you should determine that for where you would like it yourself. 5. I have not provided information on how to attach all of the pieces together, I used screws. - First I drilled a pilot hole, then recessed it some so when I drilled in the screw, it would not stick out from the wood. I also did not use any backup support to drill into, I just lined the pieces up and drilled directly into the ends. If you do this as well, make sure you are very careful when drilling your pilot holes and make sure you are going through the wood as close as possible to the center of the 5/8" thickness. If you are off by too much, the screw will end up coming through the side of a piece, or cause the wood to split and not hold the screw in place. If you choose to add extra wood backing so you have a wider area to drill into, you should be able to cut small pieces from the left over 4' x 8' sheets of wood. *** Plan out what you will do before starting construction. 6. IMPORTANT: I did not build this rig with plans for it to be easily taken apart or transported. When fully built it is too large to fit through typical doorways. Make sure that where you build it is where you are going to plan on keeping it, because you will not be able to get it out of its location unless it is disassembled. 7. You will probably want to run all the wiring for the speakers before you close in certain areas of the rig. Once it is fully assembled, it will be difficult to run certain wiring, such as the rear left surround speaker. I also would encourage you to make sure you use something to hold the wiring in place in certain areas, so if you disconnect a wire it can't fall down through a hole pass through, and be near impossible to get back out. 8. (I will add more to the list as I think of them, or are brought to my attention) I hope I have given enough information for you to complete the build as easily as possible. Some of my ticketing for the pieces and layout may be confusing though. I tried to fit everything including the dimensions onto the size of a typical sheet of paper so you can print them out and follow along without needing a computer by your side the entire time you are laying out and cutting the pieces. - Please print out all of the tickets, and use a highlighter to check off dimensions and pieces as you know they have been drawn and then cut. Thank you very much for your interest in my rig, and building it for yourself. I became inspired to build/design this rig from seeing other peoples amazing creations on this site, and I hope that I have been able to inspire you in some way to build your own rig. It really is rewarding and almost as fun as actually racing in it once you're done the build....almost. Ha. Happy Racing!!! Material required for build: (8) ---- Sheets of 8' x 4' x 5/8" wood. (8) ---- Hinges for door panels. (5) ---- Knobs/Door pulls for door panels. (1,000,000...jk) ---- Screws. Recommended tools: - Circular Saw - Jigsaw - Drill - Sander - Measuring Tape - Level - Router (for recessing holes on shifter mount) ****Please download all attachments. They are all required in order to have all information needed to cut the pieces, and build the rig. Good luck! STEP 1: BASE - P-14, (2) P-15 Hold P-15 pieces 5/8" in from the edges of piece P-14 STEP 2: BASE - (3) P-16 STEP 3: LEFT SIDE (BOTTOM) - P-1, P-2, P-3, P-4, P-5, P-6, (1) P-7, (1) P-8, (1) P-9 STEP 4: RIGHT SIDE (BOTTOM) - (1) P-7. (1) P-8, (1) P-9, P-10, P-11, P-12, P-13 I placed the amp for my transducer on piece P-10. If you choose to use an amp with transducer, this is where I would recommend you also placing the amp as it is easy to reach with your right hand. Dimensions and cutouts will need to be taken for your personal placement. You will also need to have a cutout somewhere near the rear of piece P-10 for the speaker wire to run though, to the transducer located under your seat. STEP 5: ATTACH SIDES TO BOTTOM Attach the assembled sides from Steps 3 and 4, to the bottom of the rig from Step 1 STEP 6: MONITOR STAND - P-17, P-18, (2) P-19 Pieces P-18 and (2) P-19 can be modified depending on how you choose to support your monitor. If you extend them to the back of piece P-17, and widen piece P-18, you can probably place a computer on it as well as the monitor. STEP 7: MONITOR PANEL - P-20, (2) P-21, (2) P-22 Attach pieces (2) P-21 & (2) P-22 to piece P-20 before installing piece P-20. All cutouts on P-20 will need to be determined by you based on monitor size & speaker choice. Piece sizes for (2) P-21 & (2) P-22 will be determined by monitor cutout on P-20. STEP 8: FRONT SPEAKER STANDS & SIDE SUPPORTS - (4) P-42, (2) P-43, (2) P-41 Dimensions will need to be taken. Heights and widths depend on your monitor and speaker choice, and cutout locations on piece P-20. Piece P-41 is added to help pieces P-32 & P-33 together. STEP 9: SIDES (TOP)- P-32, P-33 Piece P-32 goes above piece P-1 from Step 3. Piece P-33 goes above piece P-13 from Step 4. STEP 10: CEILING, CENTER CHANNEL & LIGHT OPENING - P-23, (2) P-24, (2) P-25, P-26, P-27, (2) P-28 Attach all pieces needed to piece P-23 before installing P-23. Verify ahead of time that your center channel speaker will fit on the base designed to hold it. STEP 11: DIVIDERS - (2) P-29, P-30, P-31 STEP 12: BACK PANEL W DOORS - P-37, (2) P-38 Hinges required to attach pieces P-38. STEP 13: FRONT PANEL W DOORS - P-34, P-35, P-36 Hinges required to attach pieces P-35 & P-36. The opening at the bottom left of piece P-34 is where I have the surge protector located. All electronics should be plugged into it, then you can run just the one power cord from the surge protector out to a wall outlet. STEP 14: ROOF W DOOR - P-39, P-40 Hinges required to attach piece P-40. STEP 15: REVERSE MOUNT PEDAL STAND - (2) P-44, P-45, P-46, P-47 Stand is optional STEP 16: BASE FOR SEAT - (2) P-54, (2) P-55 Location and height should be determined by you. (I'm missing the pictures, I will update when I find them.) STEP 17: MOUNT FOR SHIFTERS - (2) P-48, P-49, P-50, P-51, P-52, P-53 Shifter Mount is optional. Cutting the metal rods that were included with your Fanatec CSR Shifter Set will be required. The length of the metal rods, and depth/specific location of the recessed holes in the wood will need to be determined by you. If you choose to use a different shifter other than the Fanatec CSR Shifter Set, this mount will not work. FINISHED! SIMRIG "EXPLODED" VIEW (I'm missing the picture, I'll update when I find it) ****Please download all attachments. They are all required in order to have all information needed to cut the pieces, and build the rig. Good luck! The most important attachments are the "Layout Tickets" & "Piece Tickets" MBoyerRig-2dPlans.zip Piece Tickets.pdf Layout Tickets.pdf MBoyerRig-PieceMarkPictures.zip

Hello SIM racers, I'de like to leave a Basic/mid-range racing rig setup under $1500. Cockpit: Playseat Revolution, Logitech G29, PS4 1TB, 42" TV 1080p, 5.1 Channel Speakers, PVC mat... yes, we can lower the price tag under the $1000 mark on refurbished/second-hand SIM racing equipment. (for those who interested in looking for). So, let me know your likes or dislikes. All the best! Greetings.

Hello All, I'm new to iRacing, and want to build my own PC. I'm an IT guy, so I know stuff. Trying to get around $1500 without monitors. Also going to use this for RAW video editing, Here is my list. Appreciate any feedback. Is some of the stuff here overkill. I shopped NewEgg, got a price of $2500. Seems alot. These are the big items, not including fans etc. Thanks! Rudy Cooler Master HAF 932 Advanced EVGA GeForce GTX 1080 FTW DT GAMING ACX be quiet! DARK POWER PRO 11 1000W ATX 12V ASUS TUF X299 MARK 2 LGA2066 DDR4 M.2 USB 3.1 X299 ATX Motherboard for Intel Core i9 and i7 X-Series Processors Intel Core i7-7820X Skylake-X 8-Core 3.6 GHz LGA 2066 140W BX80673I77820X Desktop Processor 2 100 GB SATA SSD Drives 32GB of RAM

i have been very busy in the last couple of months designing and building my diy projects. all of these mods work on both consoles and pc, thay are powered by arduino. so no keyboard hack. and if you are familiar with arduino you can update according to your own taste. lets begin a couple of manths back i posted an e-brake build, here http://www.isrtv.com/forums/topic/21747-do-it-yourself-sequential-and-e-brake-builds/#comment-196485 then i got busy with other projects. like, DIY buuton box 5 parts.. but in the process ive come up with probably the best DIY sequential shifter ever made. lol. with a budget just below $100. exellnt quality,buils and professional look. anyway enough talk lets lets begin with the do it yourself button box and work our way to the current and latest build. please follow me at facebook here https://www.facebook.com/clos27reyes/ for early picks and sneak peak videos. and twitter here https://twitter.com/Clos27Reyes again for quick updates to projects and thoughts on new builds. thrustmaster wheel L3, R3 mod, aviation plug port diy pro build Buttonnbox button box pre build (undertaking) button box build part 5 of 5 immediately following the button box build jumped into a new build future project and builds progress on sequential shifter build sequential shifter pre build test be sure to subscribe on youtube to get notification of 1st part of sequntial shifter build being published today 9/26 @ 2pm eastern