Search the Community

Showing results for tags 'boyerm35'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Most Popular
    • Getting Started In Sim Racing
    • Sim Racing Discussion
    • Sim Gear - Buy and Sell
    • Simulation Racing Rigs / Cockpits
    • Wheel & Pedal Set Discussion
  • General Discussion
    • Inside Sim Racing Discussion
    • General + Real World Racing Discussion
    • Sim Racing Paint and Photo Shop
    • Sim Racing Videos
    • Other Gaming
  • Sim Racing Hardware
    • Audio Related
    • General Hardware Questions
    • Motion Hardware and Software Discussion
    • PC (Personal Computer) Gaming System
    • Peripherals
    • Playstation Discussion
    • Sim Vibe Hardware and Software Discussion
    • Video Related
    • Virtual Reality
    • XBox Discussion
  • Racing / Driving Games & Simulations
    • Assetto Corsa
    • Automobilista
    • Codemasters Dirt Series
    • Codemasters Formula One Series
    • Forza Motorsport Series
    • Gran Turismo Series
    • iRacing
    • Live For Speed
    • Moto GP Series
    • Project CARS 2
    • Project CARS
    • Raceroom
    • rFactor 2
    • rFactor
    • Richard Burns Rally
    • RIDE the Game
    • SimBin Studios
    • The Crew
    • WRC Series
    • General / Other Software
  • Website Discussion
    • New Website Development
    • Website Bugs
  • Archive of old sections
    • ISR Archive
    • Jessica Lopez
    • Opinion Nation
    • SSCA - Simulated Sports Car Association
    • Sim Racing League Hub
    • Top Simulation Cars of All Time
    • Throw Back Thursday

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 1 result

  1. Hello, thank you for checking out my "How to" on building my simrig! I have attached zip files for you to download that have all the information needed for every single piece to build the rig, along with plans, sections, and elevations with some dimensions for reference. I will try to explain how I chose to go about assembling it below. - Attachments are at the bottom of this post, after the pictures. **** I strongly encourage you to take time and familiarize yourself with all of the information given before you begin construction. **** A few pieces of the build will require you to take some of your own dimensions to have it work best with all of your equipment. Refer to the "Piece Tickets.pdf". - For example, you will need to take specific dimensions of the monitor you decide to use. These will be very important in determining where the cutouts will be located for the monitor and front speakers, and how large they will need to be. **** If you have any questions about anything or see that I have left out something needed to build the rig, please send me a message or reply to this topic and I will do my best to explain anything you need. I would suggest that you reply to this topic, that way if anyone else has the same question they can get an answer just by following the posts. If you decide to build my rig, I would greatly appreciate it if you could add a picture of your finished build to this topic. I am very interested to see how you will make it your own, and if you decide to make any modifications to it. Feel free to change anything you would like about the build, I have only given information for how to build my rig exactly. - If you would like to play computer games on it, I currently do not have it designed with that in mind. If you wanted to though, a simple solution would be to put your computer inside the large panel that you use to access the back of the monitor & front speakers, Depending on how large the monitor is you use, it should be able to fit inside well. I would suggest that your computer has a good cooling system in it though, because it could get quite warm being enclosed in a small area. Key things to pay attention to: 1. All of my dimensions given are based on using 5/8" thick wood. If you use any thickness other than 5/8", many dimensions will be slightly off which will cause problems with pieces lining up correctly. If you use a different thickness of wood, you will need to add/subtract the difference it makes in all pieces that would be affected. 2. I used a 32" LG monitor. I would assume you could go up to a 36", but I have not verified that, and it would still depend on the overall dimensions of the monitor, and front speakers. You will need to reference dimensions given and make sure the monitor and speakers you choose will fit inside the designated areas for them. 3. Plan out ahead of time how you plan to finish the rig off. Whether you decide to add material, paint it, stain it, etc. You should figure that out before assembling the pieces so you know how hard it will be to finish off once fully built, or how much prep work you will need to do before assembling. 4. The plans I have designed were for my own personal preference, using a Fanatec CSR Elite wheel, Fanatec CSR Elite Pedals, and Fanatec CSR Shifter Set. Please review the dimensions given and figure out if they will work well with your equipment of choice, and personal preferences. Certain dimensions were not provided (such as location of the seat, etc.) because you should determine that for where you would like it yourself. 5. I have not provided information on how to attach all of the pieces together, I used screws. - First I drilled a pilot hole, then recessed it some so when I drilled in the screw, it would not stick out from the wood. I also did not use any backup support to drill into, I just lined the pieces up and drilled directly into the ends. If you do this as well, make sure you are very careful when drilling your pilot holes and make sure you are going through the wood as close as possible to the center of the 5/8" thickness. If you are off by too much, the screw will end up coming through the side of a piece, or cause the wood to split and not hold the screw in place. If you choose to add extra wood backing so you have a wider area to drill into, you should be able to cut small pieces from the left over 4' x 8' sheets of wood. *** Plan out what you will do before starting construction. 6. IMPORTANT: I did not build this rig with plans for it to be easily taken apart or transported. When fully built it is too large to fit through typical doorways. Make sure that where you build it is where you are going to plan on keeping it, because you will not be able to get it out of its location unless it is disassembled. 7. You will probably want to run all the wiring for the speakers before you close in certain areas of the rig. Once it is fully assembled, it will be difficult to run certain wiring, such as the rear left surround speaker. I also would encourage you to make sure you use something to hold the wiring in place in certain areas, so if you disconnect a wire it can't fall down through a hole pass through, and be near impossible to get back out. 8. (I will add more to the list as I think of them, or are brought to my attention) I hope I have given enough information for you to complete the build as easily as possible. Some of my ticketing for the pieces and layout may be confusing though. I tried to fit everything including the dimensions onto the size of a typical sheet of paper so you can print them out and follow along without needing a computer by your side the entire time you are laying out and cutting the pieces. - Please print out all of the tickets, and use a highlighter to check off dimensions and pieces as you know they have been drawn and then cut. Thank you very much for your interest in my rig, and building it for yourself. I became inspired to build/design this rig from seeing other peoples amazing creations on this site, and I hope that I have been able to inspire you in some way to build your own rig. It really is rewarding and almost as fun as actually racing in it once you're done the build....almost. Ha. Happy Racing!!! Material required for build: (8) ---- Sheets of 8' x 4' x 5/8" wood. (8) ---- Hinges for door panels. (5) ---- Knobs/Door pulls for door panels. (1,000,000...jk) ---- Screws. Recommended tools: - Circular Saw - Jigsaw - Drill - Sander - Measuring Tape - Level - Router (for recessing holes on shifter mount) ****Please download all attachments. They are all required in order to have all information needed to cut the pieces, and build the rig. Good luck! STEP 1: BASE - P-14, (2) P-15 Hold P-15 pieces 5/8" in from the edges of piece P-14 STEP 2: BASE - (3) P-16 STEP 3: LEFT SIDE (BOTTOM) - P-1, P-2, P-3, P-4, P-5, P-6, (1) P-7, (1) P-8, (1) P-9 STEP 4: RIGHT SIDE (BOTTOM) - (1) P-7. (1) P-8, (1) P-9, P-10, P-11, P-12, P-13 I placed the amp for my transducer on piece P-10. If you choose to use an amp with transducer, this is where I would recommend you also placing the amp as it is easy to reach with your right hand. Dimensions and cutouts will need to be taken for your personal placement. You will also need to have a cutout somewhere near the rear of piece P-10 for the speaker wire to run though, to the transducer located under your seat. STEP 5: ATTACH SIDES TO BOTTOM Attach the assembled sides from Steps 3 and 4, to the bottom of the rig from Step 1 STEP 6: MONITOR STAND - P-17, P-18, (2) P-19 Pieces P-18 and (2) P-19 can be modified depending on how you choose to support your monitor. If you extend them to the back of piece P-17, and widen piece P-18, you can probably place a computer on it as well as the monitor. STEP 7: MONITOR PANEL - P-20, (2) P-21, (2) P-22 Attach pieces (2) P-21 & (2) P-22 to piece P-20 before installing piece P-20. All cutouts on P-20 will need to be determined by you based on monitor size & speaker choice. Piece sizes for (2) P-21 & (2) P-22 will be determined by monitor cutout on P-20. STEP 8: FRONT SPEAKER STANDS & SIDE SUPPORTS - (4) P-42, (2) P-43, (2) P-41 Dimensions will need to be taken. Heights and widths depend on your monitor and speaker choice, and cutout locations on piece P-20. Piece P-41 is added to help pieces P-32 & P-33 together. STEP 9: SIDES (TOP)- P-32, P-33 Piece P-32 goes above piece P-1 from Step 3. Piece P-33 goes above piece P-13 from Step 4. STEP 10: CEILING, CENTER CHANNEL & LIGHT OPENING - P-23, (2) P-24, (2) P-25, P-26, P-27, (2) P-28 Attach all pieces needed to piece P-23 before installing P-23. Verify ahead of time that your center channel speaker will fit on the base designed to hold it. STEP 11: DIVIDERS - (2) P-29, P-30, P-31 STEP 12: BACK PANEL W DOORS - P-37, (2) P-38 Hinges required to attach pieces P-38. STEP 13: FRONT PANEL W DOORS - P-34, P-35, P-36 Hinges required to attach pieces P-35 & P-36. The opening at the bottom left of piece P-34 is where I have the surge protector located. All electronics should be plugged into it, then you can run just the one power cord from the surge protector out to a wall outlet. STEP 14: ROOF W DOOR - P-39, P-40 Hinges required to attach piece P-40. STEP 15: REVERSE MOUNT PEDAL STAND - (2) P-44, P-45, P-46, P-47 Stand is optional STEP 16: BASE FOR SEAT - (2) P-54, (2) P-55 Location and height should be determined by you. (I'm missing the pictures, I will update when I find them.) STEP 17: MOUNT FOR SHIFTERS - (2) P-48, P-49, P-50, P-51, P-52, P-53 Shifter Mount is optional. Cutting the metal rods that were included with your Fanatec CSR Shifter Set will be required. The length of the metal rods, and depth/specific location of the recessed holes in the wood will need to be determined by you. If you choose to use a different shifter other than the Fanatec CSR Shifter Set, this mount will not work. FINISHED! SIMRIG "EXPLODED" VIEW (I'm missing the picture, I'll update when I find it) ****Please download all attachments. They are all required in order to have all information needed to cut the pieces, and build the rig. Good luck! The most important attachments are the "Layout Tickets" & "Piece Tickets" MBoyerRig-2dPlans.zip Piece Tickets.pdf Layout Tickets.pdf MBoyerRig-PieceMarkPictures.zip